Covers
Covers especially for summer protect your pool from coarse dirt, minimise the loss of temperature of the bathing water and contribute to less evaporation. Winter covers reduce the contamination of the pool water and thus the cleaning effort at the beginning of the bathing season.
At Steinbach you will find a large selection of pool covers for summer and for winter
-
![Winter covers for circular steel wall pools]()
from €59.90incl. VAT, Free shipping -
![Summer covers for round steel wall pools]()
from €47.90incl. VAT, excl. shipping -
![Winter covers for oval steel wall pools]()
from €88.90incl. VAT, Free shipping -
![Cover for Frame Pool Set Family]()
from €19.90incl. VAT, excl. shipping -
-
![Covers for Frame Pool Set]()
from €18.90incl. VAT, excl. shipping -
![Covers for Easy Set Pools]()
from €13.90incl. VAT, excl. shipping -
![Summer covers for oval steel wall pools]()
from €88.90incl. VAT, Free shipping -
![Cover for Frame Pool Set Ultra]()
from €119.00incl. VAT, Free shipping -
![Cover for Easy-Pool Ø 366 cm]()
€19.90incl. VAT, excl. shipping -
![Protective floor covers for pools 472 x 472 cm]()
€27.90incl. VAT, excl. shipping -
![Summer covers light]()
from €38.90incl. VAT, excl. shipping
Frequently asked questions for Pool covers:
This makes it easy to put the cover away without having to pump out the rainwater first. The size of the drainage holes has been chosen so that rainwater can run off but coarse dirt is retained. The ongoing cleaning effort and the use of water care products can thus be reduced.
The additional plastic strips secure your cover against lifting in the wind.
A protective ground cover is used to protect the pool liner from dirt. Before you put it on, the ground must be clean of stones, wood or similar.
Covers are laid over the entire surface of the water, pulled up to the side, placed over the handrail, folded down and then attached. This requires this excess. (Summer cover: oversize 70 cm = 35 cm per side, winter cover: oversize 130 cm = 65 cm per side) The winter cover is more oversized because the water level is lowered accordingly during the winter months.
Unfortunately, we do not have these covers in our range.
Covers for the pool
During the pool season in the summer months, a light cover is stretched over the pool to prevent gross contamination. This preserves the warmth of the bathing water and protects it from evaporation. In addition, the summer cover reduces the use of chemical water care products, as less dirt gets into the pool and less fresh water is needed. For the winter months outside the pool season, a special winter cover is recommended to avoid heavy soiling of the pool liner and the lowered water. The cleaning effort at the beginning of the bathing season is thus considerably minimised. For INTEX pools, the covers tailored to the size of the pools are suitable. These are placed directly on the pool water with the integrated overhang. The cord in the overhang allows you to fasten the cover easily and quickly. Integrated drainage holes are standard with the covers for INTEX pools. This means that rainwater does not have to be pumped away, as it can simply run off. The drainage holes are designed in such a way that they do not allow coarse dirt to pass through.
Summer cover light
The lightweight cover for summer is suitable for round steel wall pools with either 360 cm or 460 cm in diameter. It is placed directly on the water surface to protect the swimming pool from dirt and the water from evaporation. It is attached to the side by means of eyelets and cord. An oversize of 40 cm ensures an optimal fit. The sheet comes with a blue top and a black bottom and is made of 86 g/m2 polyethylene.
The summer cover light is available for round steel wall pools with the following diameters:
- Ø 360 cm, Manufacturing dimension Ø 400 cm
- Ø 460 cm, Manufacturing dimension Ø 500 cm
Summer cover EXTRA for round steel-walled pools
The 94 g/m2 polyethylene cover is used for round steel-walled pools in the summer months to prevent dirt from entering and thus maintain the cleanliness of the pool water. The cover minimises heat loss and evaporation of the water and thus the need for chemical maintenance products. The cover is laid directly on the water surface and is fastened at the side by means of a tension cord and ratchet. An oversize of 70 cm ensures an optimal fit. The foil is supplied with a blue top side and a black underside.
The summer cover EXTRA is available for round steel-walled pools with the following diameters:
- Ø 360 cm, Manufacturing dimension ca. Ø 430 cm
- Ø 400 cm, Manufacturing dimension ca. Ø 470 cm
- Ø 460 cm, Manufacturing dimension ca. Ø 530 cm
- Ø 500 cm, Manufacturing dimension ca. Ø 570 cm
- Ø 550 cm, Manufacturing dimension ca. Ø 620 cm
- Ø 600 cm, Manufacturing dimension ca. Ø 670 cm
Summer cover EXTRA for oval steel-walled pools
The summer cover EXTRA made of 94 g/m2 polyethylene is suitable for oval steel-walled pools to protect them from coarse dirt and thus maintain the cleanliness of the bathing water. By using the cover, you prevent the loss of heat and water due to evaporation. This additionally reduces the need for chemical maintenance products. The cover is placed directly on the water surface, and is fastened at the side by means of a tension cord and ratchet. An oversize of 70 cm ensures an optimal fit. The sheet is supplied with a blue top side and a black underside.
The summer cover EXTRA is available for oval steel wall pools with the following dimensions in length and width:
- 550 x 360 cm, Manufacturing dimension ca. 620 x 410 cm
- 640 x 360 cm, Manufacturing dimension ca. 710 x 430 cm
- 730 x 370 cm, Manufacturing dimension ca. 800 x 440 cm
Winter cover EXTRA for round steel-walled pools
The winter cover EXTRA made of reinforced 120 g/m2 polyethylene is attached over your steel-walled pool outside the bathing season with a tension cord and ratchet to protect the pool liner and the sunken water from coarse dirt. This reduces the cleaning effort and the use of pool chemicals at the beginning of the bathing season. The lateral oversize is 130 cm for an optimal fit. The colour of the cover is green on top and black on the underside.
The winter cover EXTRA for round steel shell pools is available in dimensions in lenght and width:
- Ø 360 cm, Manufacturing dimension ca. Ø 490 cm
- Ø 400 cm, Manufacturing dimension ca. Ø 530 cm
- Ø 460 cm, Manufacturing dimension ca. Ø 590 cm
- Ø 500 cm, Manufacturing dimension ca. Ø 630 cm
- Ø 550 cm, Manufacturing dimension ca. Ø 680 cm
- Ø 600 cm, Manufacturing dimension ca. Ø 730 cm
Winter cover EXTRA for oval steel wall pools
The winter cover EXTRA is suitable for wintering oval steel shell pools and is fastened with a tension cord and ratchet. The material is made of reinforced 120 g/m2 polyethylene, the lateral oversize is 130 cm. By using a winter cover, you prevent the penetration of coarse dirt and thus reduce the cleaning effort at the beginning of the new pool season. The colour of the cover is green on the top and black on the bottom.
The winter cover EXTRA for oval steel shell pools is available for the following dimensions in length and width:
- 550 x 360 cm, Manufacturing dimension ca. 680 x 490 cm
- 620 x 360 cm, Manufacturing dimension ca. 750 x 490 cm
- 730 x 370 cm, Manufacturing dimension ca. 860 x 500 cm
Cover for INTEX Easy Set Pools®
The cover made of 0.18 mm thick vinyl is suitable for the round above-ground pool Easy Pool Set. During the bathing season, it offers protection from coarse dirt, reduces evaporation and keeps your pool water clean and at the desired temperature for longer. It is attached by means of a circumferential cord. The drainage holes ensure that rainwater runs off. The overhang is approx. 30 cm.
The cover for INTEX Easy Set Pools® is available for pools with the following diameters:
- Ø 244 cm, Manufacturing dimension Ø ca. 274 cm
- Ø 305 cm, Manufacturing dimension Ø ca. 335 cm
- Ø 366 cm, Manufacturing dimension Ø ca. 396 cm
- Ø 396 cm, Manufacturing dimension Ø ca. 426 cm
- Ø 457 cm, Manufacturing dimension Ø ca. 487 cm
Covers for INTEX Frame Pool Prism Rondo
The cover made of 0.18 mm thick vinyl is suitable for your round or octagonal Frame Pool Prism Rondo by INTEX. This prevents the unwanted penetration of dirt and evaporation of water. Your bathing water stays clean and warm for longer.
The cover is attached by means of a circumferential cord. The drainage holes ensure that rainwater runs off. The overhang is approx. 25 cm in each case.
The cover for INTEX Frame Pool Prism Rondo is available for pools with the following diameters:
- Ø 305 cm, Manufacturing dimension Ø ca. 330 cm
- Ø 366 cm, Manufacturing dimension Ø ca. 391 cm
- Ø 457 cm, Manufacturing dimension Ø ca. 482 cm
Deluxe covers for INTEX Frame Pool Ultra
The Deluxe cover is made of UV-resistant polyethylene material. It not only prevents the loss of heat and evaporation of the pool water, but also keeps coarse dirt out. The cover is attached with a circumferential cord, and the additional plastic strings secure your cover so that it cannot be lifted off in windy conditions.
The drainage holes allow rainwater to run off, but do not let dirt through. The overhang is approx. 20 cm.
The Deluxe Cover for INTEX Frame Pool Ultra is available for pools with the following diameters:
- Ø 488 cm, Manufacturing dimension Ø ca. 508 cm
- Ø 549 cm, Manufacturing dimension Ø ca. 569 cm
Cover for Frame Pool Prism Quadra 400 x 200 cm
The cover protects your Frame Pool Prism Quadra with the dimensions 400 x 200 cm in length and width from dirt and preserves the warmth of the pool water. The cover is made of 0.18 mm thick vinyl and has an overhang of approx. 20 cm at the sides. The cover is simply attached with the chord supplied. When it rains, the rainwater can simply run off through the integrated drainage holes.
Cover for Frame Pool Family
The cover is suitable for the Frame Pool Family models by INTEX and consists of 0.18 mm thick vinyl. It protects your pool from dirt, evaporation and heat loss. It is attached with the included cord at specific points. Rainwater can run off easily via the drainage holes without coarse dirt getting into the pool.
The lateral overhang is approx. 20 cm.
The cover for INTEX Frame- Pool Family is available for pools with the following dimensions in length and width:
- 300 x 200 cm, Manufacturing dimension ca. 320 x 220 cm
- 460 x 226 cm, Manufacturing dimension ca. 480 x 246 cm