Degrii Zima Lite
- Cordless design for maximum flexibility
- Ultrasonic radar technology for efficient cleaning
- 3 motors for outstanding suction power
- Long battery life
- Intelligent app control
Sold Out
The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.
Product information
The Degrii Zima Lite is the world's first intelligent cordless pool cleaner with ultrasonic radar and revolutionises pool cleaning with innovative technology. Its cordless design ensures increased safety and offers greater flexibility and convenient handling without restrictions.
Technically, the Degrii Zima Lite impresses with a pump capacity of 15.141 l/h, a cleaning element width of 325 mm and a speed of 12 m/min. It can dive to a depth of 4 m and is suitable for salt water. The cleaner works optimally at water temperatures between 5°C - 35°C and an ambient temperature of 5°C - 40°C. It is suitable for pools with a floor area of up to 150 m².
Thanks to the precision of the ultrasonic radar, the pool robot can clean efficiently and reach all corners. The three powerful motors ensure that almost any type of dirt is removed effortlessly. The Degrii Zima Lite is suitable for efficient cleaning of all surfaces - from the floor and walls to the waterline.
With a battery life of up to 180 min, the pool robot offers constant performance. The large battery with 9.300 mAh capacity ensures long cleaning cycles. The 180 μm ultra-fine filter absorbs even the smallest particles and ensures crystal-clear water.
The intelligent app control of the Degrii Zima Lite allows you to choose between several cleaning modes (overall, floor and wall cleaning), lift the cleaner with one click and plan cleaning processes according to your individual requirements.
The Degrii Zima Lite ensures that your pool is always perfectly clean and offers an effortless and efficient cleaning solution.
Ultrasonic radar for precise cleaning
Thanks to the efficient cleaning in an N-shaped pattern, the pool robot reaches all corners of the pool.
Up to 3h battery runtime
Powered by a powerful battery, the Zima Lite can clean for up to 3 hours on a single charge, allowing up to 5 complete cleaning runs of private pools on one charge.
Cordless convenience
Enjoy increased safety and greater flexibility thanks to the cordless design.
More than 200W suction power
With its impressive suction power, the Zima Lite can efficiently pick up particles and fine debris, providing a deep clean that leaves your pool fresh and clean.
Pool runner:
Operating mode: App control, automatic cleaning
Cleaning area: floor cleaning
wall cleaning
waterline
Suitable for saltwater: yes
Pump capacity: 15.141 l/h
Width of cleaning element: 325 mm
Speed: 12 m/min
Immersion depth: 4 m
Filter mesh: 180 μm
Safety class: IPX8
Water temperature: 5°C - 35°C
Ambient temperature: 5°C - 40°C
Pool size - floor area: 150 m²
Verbindung:
App control: yes
Connection type: WiFi, Bluetooth
App name (APP store): Degrii OS
Connection WiFi:
Connection type WiFi: yes
Transmission frequency: 2.400 - 2.483,5 MHz
Effective radiated power ERP: ≤ 15,1 dBM
Connection Bluetooth:
Connection type Bluetooth: yes
Transmission frequency: 2.402 - 2.480 MHz
Effective radiated power ERP: ≤ 4,1 dBM
Rechargeable Battery:
Type of rechargeable battery: Lithium ions
Rechargeable battery capacity: 9.300 mAh
Charging time: 3 h - 4 h
Battery running time: 180 min
Charger:
Charger rated power: 63,75 W
Charger energy power: 100-240V~ / 50-60Hz
Charger unit output voltage: 25,5 V
Charger safety class: IP30
FAQs from category Pool robots:
Do not leave the cable in the pool all the time. After each use, remove it from the pool and unplug and turn off the cord. Wash the cable with clean water to remove chemical residues after each cleaning operation. Put the cable length into the pool according to pool dimensions, place the remaining cable at the pool edge, i.e. pull overflown cable out of the water. Place obstacles such as built-in pool ladders/installation ladders out of the pool to prevent the cable from getting caught.
Position the power supply so that the cleaner can easily reach all areas. Switch off the filter pump while cleaning with the pool vacuum. Enter the maximum possible length of the connection cable in the pool, but take into account a corresponding minimum distance between the control unit and the pool. Change the setting of the nozzles.
Clean the filter container/filter bag and remove slippery debris such as algae from the pool walls. Put the pool vacuum cleaner into the pool at the optimum water temperature. This is between 10°C and 35°C. Check the drive belts and brushes for wear and replace them if necessary. Set the PH value correctly. This should be between 7.0 and 7.2. Switch off the unit and let all the air escape. Mount the additional buoyancy aids from the scope of delivery.
Check the plug of the power cord and the control unit or the battery. Plug the control unit directly into a socket and do not use extension cables. Check your house line for overload, the socket may be defective. Contact a qualified electrician.
There is air in the pool vacuum, switch off the unit, let all the air escape and let the pool vacuum sink to the ground. If necessary, adjust the salt content correctly.
Check the wheels/drive belts for wear and foreign objects in the drive. Replace the wheels/drive belts if necessary.
Check whether the water level in the pool is too high and drain the water if necessary. If your pool liner is a little rough, the pool vacuum will have more grip. Carry out a reduction of the buoyancy. If you have a salt water pool, the buoyancy is slightly higher in salt water; reduce the buoyancy.
It is necessary to weigh down the pool vacuum cleaner. A weight must be installed for this purpose. Please contact our Service Centre.
Our pool vacuums were designed for liner pools, the above materials have no grip or adhesion for the pool vacuum because the surfaces are too smooth.
Pull the cleaning hose and lift the automatic vacuum pool cleaner from the pool floor. The pool floor may be wrinkled, preventing the vacuum cleaner from moving. Check the water flow and make sure that the filter pump is switched on and has the appropriate power. Make sure that the gate valves are open. Clean or change the filter cartridge. For sand filter systems, you must backwash the filter.
You need to unblock or remove the cleaning lips because the sail, water outlet nozzle or cleaning lip may be stuck.
The buoyancy aids must be glued onto the inside of the upper part of the device - ideally offset and not directly next to each other.
The pool robot beeps when the ON/OFF button is pressed outside the water. This is due to the integrated water sensor. Put the pool robot into the water and after 15 seconds it will start cleaning the pool.
Press the ON/OFF button on the underside of the pool robot until you feel it click into place. If the ON/OFF button is pressed outside the water, the device beeps and does not switch on due to the integrated water sensor. Place the pool robot in the water. Please note: The pool robot only starts cleaning 15 seconds after it has been placed in the water.
All pool robots from Steinbach and INTEX are suitable for salt water as long as the salt content in the water is below 0.5 % (salt electrolysis). Clean the pool robot thoroughly with clear water after each use. (Info: This removes chlorine and salt water residues - so the material is preserved for a long time and also does not fade as quickly).