Steinbach
Poolrunner Battery Basic
- Battery-powered swimming pool cleaner for optimum floor cleaning
- Built-in "touch and reverse" technology
- Rounded edges for higher protection of the pool liner
- Extra light for easy handling
Sold Out
The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.
Product information
The fully automatic, battery-powered Steinbach Poolrunner Battery+ is used to clean all pools with flat floors. It uses a built-in, rechargeable battery, is wireless and therefore suitable for all pool sizes. We recommend the use of this vacuum for pools up to 10 m² and a maximum pool depth of 2,00 m. The cleaner uses a 12,6 V DC motor with jet drive exclusively for cleaning floor surfaces. The rounded edges of the Poolrunner Battery Basic provide the highest possible protection for your pool liner and the built-in "Touch and Reverse" technology makes it ideal for foil pools. With the integrated brush on the bottom and a filter fineness of 180 μm, the poolroboter is perfect to remove impurities from your pool and ensures crystal clear pool water. At a water temperature of at least 10°C - 35°C, the battery life is up to 60 min. The rechargeable lithium ion battery with battery capacity of 2.600 mAh, requires a charging time of 3 h - 4 h.
Pool runner:
Operating mode: Rechargeable battery
Cleaning area: floor cleaning
Suitable for saltwater: yes
Pump capacity: 6.000 l/h
Width of cleaning element: 200 mm
Speed: 16 m/min
Immersion depth: 2,00 m
Filter mesh: 180 μm
Safety class: IPX8
Water temperature: 10°C - 35°C
Ambient temperature: 10°C - 40°C
Pool size - floor area: 10 m²
Connection:
App control: no
Connection type: no
App name (APP store): nein
Rechargeable Battery:
Type of rechargeable battery: Lithium ions
Rechargeable battery capacity: 2.600 mAh
Charging time: 3 h - 4 h
Battery running time: 60 min
Charger:
Charger rated power: 29 W
Charger energy power: 220-240V~ / 50Hz
Charger unit output voltage: 12,6 V
Charger safety class: IP20
FAQs for Poolrunner Battery Basic:
FAQs from category Pool robots:
Do not leave the cable in the pool all the time. After each use, remove it from the pool and unplug and turn off the cord. Wash the cable with clean water to remove chemical residues after each cleaning operation. Put the cable length into the pool according to pool dimensions, place the remaining cable at the pool edge, i.e. pull overflown cable out of the water. Place obstacles such as built-in pool ladders/installation ladders out of the pool to prevent the cable from getting caught.
Position the power supply so that the cleaner can easily reach all areas. Switch off the filter pump while cleaning with the pool vacuum. Enter the maximum possible length of the connection cable in the pool, but take into account a corresponding minimum distance between the control unit and the pool. Change the setting of the nozzles.
Clean the filter container/filter bag and remove slippery debris such as algae from the pool walls. Put the pool vacuum cleaner into the pool at the optimum water temperature. This is between 10°C and 35°C. Check the drive belts and brushes for wear and replace them if necessary. Set the PH value correctly. This should be between 7.0 and 7.2. Switch off the unit and let all the air escape. Mount the additional buoyancy aids from the scope of delivery.
Check the plug of the power cord and the control unit or the battery. Plug the control unit directly into a socket and do not use extension cables. Check your house line for overload, the socket may be defective. Contact a qualified electrician.
There is air in the pool vacuum, switch off the unit, let all the air escape and let the pool vacuum sink to the ground. If necessary, adjust the salt content correctly.
Check the wheels/drive belts for wear and foreign objects in the drive. Replace the wheels/drive belts if necessary.
Check whether the water level in the pool is too high and drain the water if necessary. If your pool liner is a little rough, the pool vacuum will have more grip. Carry out a reduction of the buoyancy. If you have a salt water pool, the buoyancy is slightly higher in salt water; reduce the buoyancy.
It is necessary to weigh down the pool vacuum cleaner. A weight must be installed for this purpose. Please contact our Service Centre.
Our pool vacuums were designed for liner pools, the above materials have no grip or adhesion for the pool vacuum because the surfaces are too smooth.
Pull the cleaning hose and lift the automatic vacuum pool cleaner from the pool floor. The pool floor may be wrinkled, preventing the vacuum cleaner from moving. Check the water flow and make sure that the filter pump is switched on and has the appropriate power. Make sure that the gate valves are open. Clean or change the filter cartridge. For sand filter systems, you must backwash the filter.
You need to unblock or remove the cleaning lips because the sail, water outlet nozzle or cleaning lip may be stuck.
The buoyancy aids must be glued onto the inside of the upper part of the device - ideally offset and not directly next to each other.
The pool robot beeps when the ON/OFF button is pressed outside the water. This is due to the integrated water sensor. Put the pool robot into the water and after 15 seconds it will start cleaning the pool.
Press the ON/OFF button on the underside of the pool robot until you feel it click into place. If the ON/OFF button is pressed outside the water, the device beeps and does not switch on due to the integrated water sensor. Place the pool robot in the water. Please note: The pool robot only starts cleaning 15 seconds after it has been placed in the water.
All pool robots from Steinbach and INTEX are suitable for salt water as long as the salt content in the water is below 0.5 % (salt electrolysis). Clean the pool robot thoroughly with clear water after each use. (Info: This removes chlorine and salt water residues - so the material is preserved for a long time and also does not fade as quickly).