Steinbach Steinbach

Filter pump SPS 75-1 (T)

Art.
  • Powerful filter pump
  • High-quality plastic
  • Self-priming pump with pre-filter

Sold Out

The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.

* Mandatory Field

from €139.00
incl. VAT, Free shipping
Only %1 left

Only items left in stock

The minimum order quantity is 1

Product information

Pool pumps are the powerhouse of the pool circuit. The Filter pump SPS 75-1 (T) has a pump capacity of . The connection is / . This filter pump can be used for pools with approx. water capacity. The hose connection is . The pump can be used up to a maximum water temperature of 35 °C.

Salt water suitable: yes
Water capacity: 33.000 l
Pump power: 8.500 l/h
Power supply: 220-240V~ / 50Hz
Input power maximum: 450 W
Transformer: no
Delivery head: 9,00 m
Operating principle: self-priming
Pre-filter: yes
Timer present: no
Connection size: Ø 32/38 mm
*Sound pressure level: < 70 dB(A)
Protection class: IPX5
Insulation class: F
Cable length to unit: 1,60 m
Water temperature: 10°C - 35°C


*Emission sound level comparable to a large household appliance

02 Transparent prefilter cover
€14.90
incl. VAT, excl. shipping
04 SPS mechanical seal
€17.90
incl. VAT, excl. shipping
07 SPS screen basket
€11.90
incl. VAT, excl. shipping
12 Drain screw, including seal
€4.99
incl. VAT, excl. shipping
€3.49
incl. VAT, excl. shipping
€2.99
incl. VAT, excl. shipping

FAQs from category Filter pumps:

All Steinbach and INTEX filter systems (sand filter systems, cartridge filter systems & filter pumps) are suitable for salt water as long as the salt content in the water is below 0.5 % (salt electrolysis). Before winterising, clean the filter system thoroughly with standard bathroom cleaner, clear tap water and a lint-free cloth.

All filter systems and filter pumps have a sound pressure level* of < 70 dB(A).

*The emission volume is comparable to a large household appliance.

In this case, the filter medium used is often contaminated. The filter medium used (quartz filter sand or filter balls) is subject to a certain amount of wear and tear, even when operated as intended under optimal conditions, and should be replaced at regular intervals, depending on the operating time and degree of contamination. For sand filter systems, switch off the pump and then set the filter setting to ‚Rückspülen/backwash'. Switch the filter system on again. Carry out the backwash process until clean water comes out of the backwash line (max. 2 minutes). When using Filter Balls, do not backwash. If the filter performance decreases, we recommend washing the Filter Balls by hand. If necessary, the Filter Balls should be replaced. In cartridge filter systems, the filter medium should be changed approx. every 2 weeks.

If the pressure is too low, the pre-filter is dirty and the pump is not getting enough water. Clean the pre-filter and check the suction line and the water level.

If the sand is newly filled in, or the sand is already very fine due to the use of several seasons, small sand particles may still be present. The solution is to backwash several times until the water comes out clear, or to fill in new sand.

The filter system should always be the first part in the water treatment system. The rest of the pool accessoires should only be connected after the filter system. A heat pump should ideally always be the last part in the water treatment system, so that the filtered, treated water flows through the heat pump and the path of the heated water into the pool is as short as possible.

Symbol photos

The pictures shown are just for reference, the actual product may differ.